目录

• 1.产品概述       2.产品特点     6X4嘉泰姆

• 3.应用范围       4.技术规格书下载（PDF文档）6X4嘉泰姆

• 5.产品封装       6.电路原理图  6X4嘉泰姆

• 7.相关产品6X4嘉泰姆

   产品概述 返回TOP6X4嘉泰姆

TheCX24C512 CX24C512G are EEPROM devices that use the industrial standard 2-wire interface for communications. The CX24C512 CX24C512G contains a memory array of 512K-bits (65,536x8), which is organized in 128-byte per page. The EEPROM can operate in a wide voltage range from 1.7V to 5.5V which fits most application. This product can provide a low-power 2-wire EEPROM solution. The device is offered in Lead-free, RoHS, halogen free or Green. The available package types are 8-pin SOIC/SOP, TSSOP, DFN and CSP. The CX24C512 CX24C512Gis compatible with the industrial standard 2-wire bus protocol. If in case the bus is not responded, a new sent Op-code command will reset the bus and the device will respond correctly. The simple bus consists of the Serial Clock wire (SCL) and the Serial Data wire (SDA). Utilizing such bus protocol, a Master device, such as a microcontroller, can usually control one or more Slave devices, alike this CX24C512G The bit stream over the SDA line includes a series of bytes, which identifies a particular Slave device, an instruction, an address within that Slave device, and a series of data, if appropriate. The CX24C512Galso has a Write Protect pin (WP) to allow blocking any write operations over specified memory area. Under no circumstance, the device will be hung up. In order to refrain the state machine entering into a wrong state during power-up sequence or a power toggle off-on condition, a power on reset circuit is embedded. During power-up, the device does not respond to any instructions until the supply voltage (VCC) has reached an acceptable stable level above the reset threshold voltage. Once VCC passes the power on reset threshold, the device is reset and enters into the Standby mode. This would also avoid any inadvertent Write operations during power-up stage. During power-down process, the device will enter into standby mode, once VCC drops below the power on reset threshold voltage. In addition, the device will be in standby mode after receiving the Stop command, provided that no internal write operation is in progress. Nevertheless, it is illegal to send a command unless the VCC is within its operating level.

   产品特点 返回TOP6X4嘉泰姆

 Two-Wire Serial Interface, I2C TM Compatible 6X4嘉泰姆

– Bi-directional data transfer protocol 6X4嘉泰姆

 Wide-voltage Operation – VCC = 1.7V to 5.5V 6X4嘉泰姆

 Speed: 400 KHz (1.7V) and 1 MHz (2.5V~5.5V) 6X4嘉泰姆

 Standby current (max.): 1A, 1.7V 6X4嘉泰姆

 Operating current (max.): 2 mA, 1.7V 6X4嘉泰姆

 Hardware Data Protection – Write Protect Pin 6X4嘉泰姆

 Sequential & Random Read Features 6X4嘉泰姆

 Memory organization: 65,536 x 8 bits 6X4嘉泰姆

 Page Size: 128 bytes 6X4嘉泰姆

 Page write mode 6X4嘉泰姆

– Up to 128 bytes per page write 6X4嘉泰姆

 Self timed write cycle with auto clear: 5ms (max.) 6X4嘉泰姆

 Filtered inputs for noise suppression 6X4嘉泰姆

 High-reliability 6X4嘉泰姆

– Endurance: 1 million cycles 6X4嘉泰姆

– Data retention: 100 years 6X4嘉泰姆

 Industrial temperature grades 6X4嘉泰姆

 Packages: SOIC/SOP, TSSOP, DFN and CSP 6X4嘉泰姆

 Lead-free, RoHS, Halogen free, Green6X4嘉泰姆

   应用范围 返回TOP6X4嘉泰姆

   a6X4嘉泰姆

   技术规格书（产品PDF) 返回TOP 6X4嘉泰姆

     需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！6X4嘉泰姆

 6X4嘉泰姆

产品封装图 返回TOP6X4嘉泰姆

6X4嘉泰姆

电路原理图 返回TOP6X4嘉泰姆

6X4嘉泰姆

相关芯片选择指南 返回TOP