目录RPl嘉泰姆

   1.产品概述      2.产品特点      3.应用范围     4.技术规格书下载（PDF文档）RPl嘉泰姆

   5.产品封装      6.电路原理图     7.相关产品RPl嘉泰姆

一.产品概述RPl嘉泰姆

    The CXDC6582 is a continuous conduction mode inductive step-down converter, designed for driving single or multiple series connected LED efficiently from a voltage source higher than the total LED chain voltage. RPl嘉泰姆

    The device operates from an input supply between 7V and 60V and provides an externally adjustable output current of up to 1A. Depending upon the supply voltage and external components, the CXDC6582 can provide max. 30 watts of output power. RPl嘉泰姆

    The CXDC6582 includes the power switch and a high-side output current sensing circuit, which uses an external resistor to set the nominal average output current, and a dedicated DIM input accepts either a DC voltage or a wide range of pulsed dimming. Applying a voltage of 0.3V or lower to the DIM pin turns the output off and switches the device into a low current standby state. RPl嘉泰姆

   The CXDC6582 is available in PSOP-8 (ESOP8) with power pad packages. RPl嘉泰姆

二.产品特点RPl嘉泰姆

  Low components countRPl嘉泰姆

  Wide input voltage range: 7V to 60VRPl嘉泰姆

  Up to 1A output currentRPl嘉泰姆

  Linear and PWM dimming capabilityRPl嘉泰姆

  Up to 1MHz switching frequencyRPl嘉泰姆

  Typical 5% output current accuracyRPl嘉泰姆

  Open/short circuit LED protectionRPl嘉泰姆

  High efficiency (up to 97%)RPl嘉泰姆

  High-Side Current SenseRPl嘉泰姆

  Hysteretic Control: No CompensationRPl嘉泰姆

  Constant current LED driverRPl嘉泰姆

三.应用范围RPl嘉泰姆

  DC/DC LED driver applicationsRPl嘉泰姆

  Automotive lightingRPl嘉泰姆

  General purpose constant current sourceRPl嘉泰姆

  LED back-up lightingRPl嘉泰姆

  SELV lightingRPl嘉泰姆

  Backlighting for flat panel displays    RPl嘉泰姆

四.技术规格书（产品PDF)RPl嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！RPl嘉泰姆

 RPl嘉泰姆

五.产品封装图RPl嘉泰姆

 RPl嘉泰姆

   出色的调光特性，非常高的效率，宽电压输入，简洁的外围电路。 CXDC6582 专为 LED 背光---车灯---LED 照明的各种恒流应用打造。 RPl嘉泰姆

六.电路原理图RPl嘉泰姆

 RPl嘉泰姆

    The CXDC6582 allow dimming with a PWM signal at the DIM input. A logic level below 0.3V at DIM forces to turn off the LED and the logic level at DIM must be at least 2.5V to turn on the full LED current. The frequency of PWM dimming ranges from 100Hz to more than 20 kHz. The DC voltage is valid from 0.5V to 2.5V. When the dc voltage is higher than 2.5V, the output current keeps constant. Constant LED current : I=100mV/Rs  RPl嘉泰姆

七.相关芯片选择指南       更多同类产品......RPl嘉泰姆